Ohms to Megaohms Calculator

Direct answer

Multiply the entered ohms value by 0.000001 to express it in megaohms (MΩ). This converts ohm (Ω) to megaohm (MΩ) within the documented electrical resistance family.

Variables and formula

• Ohms (Ω): the source value measured in ohm.
• Megaohms (MΩ): the same quantity expressed in megaohm.
• Conversion factor: 0.000001 megaohms per ohm.

Megaohms = Ohms × 0.000001

The generator emits numeric factors with at most 15 significant digits. Calculator results keep up to 10 significant digits for display; this formatting does not increase the precision of the measurement.

Unit definitions and named variants

Source unit: ohm (Ω). The ohm is the coherent SI derived unit of electrical resistance: 1 Ω = 1 V/A. Named variant used: Scalar electrical resistance. Reference: Bureau International des Poids et Mesures: The International System of Units (SI), 9th edition, version 4.01.

Target unit: megaohm (MΩ). A megaohm is the SI decimal multiple formed by applying mega (10^6) to ohm: 1 MΩ = 1000000 Ω. Named variant used: Scalar electrical resistance. Reference: Bureau International des Poids et Mesures: The International System of Units (SI), 9th edition, version 4.01.

The Ω-to-MΩ direction remains inside the electrical resistance quantity; it changes the unit label and numerical scale, not the kind of quantity being measured.

Relationship and precision

The named unit relationships are defined or exact, so the conversion is exact before display rounding and source-measurement uncertainty.

• Ω relationship: The base factor is exactly 1 by the family base-unit choice.
• MΩ relationship: The decimal-prefix relationship is exact.

To audit the factor through the family base unit, divide the raw dataset factors 1 by 1000000. The generator emits that quotient once at 15 significant digits as the canonical direct factor 0.000001; runtime calculations do not divide the already-emitted base factors again.

Reproducible example

For 10 ohms, 10 × 0.000001 = 0.00001 megaohms. Repeating the same multiplication with the stated factor reproduces the displayed conversion before interface rounding.

Directional scale check

Because one ohm contains 0.000001 megaohms, the target number is smaller than the source number for every positive input. Zero maps to zero, while negative inputs are rejected because this family models non-negative magnitudes.

Interpretation

Read the result as megaohms, not ohms. A value entered as Ω leaves the calculator labelled MΩ; this directional distinction matters even when the two units describe the same electrical resistance quantity.

Assumptions and limitations

• Only non-negative resistance magnitudes are accepted by this family.
• The ohm symbol is Greek capital omega (Ω), not the Latin letter O or the numeral zero.
• A conversion does not add significant figures to the source measurement.

Common mistakes

• Ω is the unit symbol; O and 0 are not valid substitutes.
• Megohm is a common spelling, but megaohm follows the full SI prefix name.

Continue within the Electrical Resistance family

See the Electrical Resistance conversion hub for its five-unit reference table and all 20 directed routes.

• Reverse the direction: Megaohms to Ohms
• Compare another electrical resistance route: Ohms to Milliohms
• Compare another electrical resistance route: Ohms to Kiloohms
• Compare another electrical resistance route: Ohms to Gigaohms
• Compare another electrical resistance route: Megaohms to Milliohms

Assumptions

• The entered value uses ohms exactly as labelled.
• Only non-negative resistance magnitudes are accepted by this family.
• Rounding and measurement uncertainty remain the user's responsibility.

Sources and methodology

CalcMotive publishes the formula and assumptions so you can decide whether the estimate fits your use case. See our methodology standards.

• The International System of Units (SI), 9th edition, version 4.01; Bureau International des Poids et Mesures; accessed Aug 7, 2026