Bar to Pascals Calculator

Direct answer

Multiply the entered bar value by 100000 to express it in pascals (Pa). This converts bar (bar) to pascal (Pa) within the documented pressure family.

Variables and formula

• Bar (bar): the source value measured in bar.
• Pascals (Pa): the same quantity expressed in pascal.
• Conversion factor: 100000 pascals per bar.

Pascals = Bar × 100000

The generator emits numeric factors with at most 15 significant digits. Calculator results keep up to 10 significant digits for display; this formatting does not increase the precision of the measurement.

Unit definitions and named variants

Source unit: bar (bar). The bar is a non-SI pressure unit defined as 0.1 MPa or exactly 100,000 Pa. Named variant used: Pressure unit bar; not the unrelated typographic or musical word. Reference: Bureau International des Poids et Mesures: The International System of Units (SI), 9th edition, version 4.01; National Institute of Standards and Technology: NIST Guide to the SI, Appendix B.8: Factors for Units Listed Alphabetically.

Target unit: pascal (Pa). The pascal is the coherent SI unit of pressure and stress: 1 Pa = 1 N/m² = 1 kg·m⁻¹·s⁻². The canonical pascal definition is used; no alternate named variant is implied. Reference: Bureau International des Poids et Mesures: The International System of Units (SI), 9th edition, version 4.01; National Institute of Standards and Technology: NIST Handbook 44 (2026), Appendix C: General Tables of Units of Measurement.

The bar-to-Pa direction remains inside the pressure quantity; it changes the unit label and numerical scale, not the kind of quantity being measured.

Relationship and precision

The named unit relationships are defined or exact, so the conversion is exact before display rounding and source-measurement uncertainty.

• bar relationship: The relationship to the pascal is exact.
• Pa relationship: The base factor is exactly 1 by the family base-unit choice.

To audit the factor through the family base unit, divide the raw dataset factors 100000 by 1. The generator emits that quotient once at 15 significant digits as the canonical direct factor 100000; runtime calculations do not divide the already-emitted base factors again.

Reproducible example

For 10 bar, 10 × 100000 = 1000000 pascals. Repeating the same multiplication with the stated factor reproduces the displayed conversion before interface rounding.

Directional scale check

Because one bar contains 100000 pascals, the target number is larger than the source number for every positive input. Zero maps to zero, while negative inputs are rejected because this family models non-negative magnitudes.

Interpretation

Read the result as pascals, not bar. A value entered as bar leaves the calculator labelled Pa; this directional distinction matters even when the two units describe the same pressure quantity.

Assumptions and limitations

• Only non-negative pressure magnitudes are accepted; negative gauge readings require a signed, reference-aware model.
• Input and output must refer to the same pressure reference and measurement conditions; a unit conversion alone cannot change the reference datum.
• Psi means pound-force per square inch (lbf/in²) using standard gravity, not pound-mass per square inch.

Common mistakes

• bar and barg are not identical labels: barg explicitly denotes gauge reference.
• Pa is pressure; P is not the unit symbol.

Continue within the Pressure family

See the Pressure conversion hub for its five-unit reference table and all 20 directed routes.

• Reverse the direction: Pascals to Bar
• Compare another pressure route: Bar to Kilopascals
• Compare another pressure route: Bar to Pounds-force per square inch
• Compare another pressure route: Bar to Standard atmospheres
• Compare another pressure route: Pascals to Kilopascals

Assumptions

• The entered value uses bar exactly as labelled.
• Only non-negative pressure magnitudes are accepted; negative gauge readings require a signed, reference-aware model.
• Rounding and measurement uncertainty remain the user's responsibility.

Sources and methodology

CalcMotive publishes the formula and assumptions so you can decide whether the estimate fits your use case. See our methodology standards.

• The International System of Units (SI), 9th edition, version 4.01; Bureau International des Poids et Mesures; accessed Aug 7, 2026
• NIST Guide to the SI, Appendix B.8: Factors for Units Listed Alphabetically; National Institute of Standards and Technology; accessed Aug 7, 2026
• NIST Handbook 44 (2026), Appendix C: General Tables of Units of Measurement; National Institute of Standards and Technology; accessed Aug 7, 2026